Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: Added note which service objects get synced
Section
Column
width300px

Table of Contents
 

Column
width400px
Panel
bgColor#f4f4f4
titleRelated Articles
Column
width400px

Filter by label (Content by label)
showLabelsfalse
max5
spacesSPAG
showSpacefalse
sortmodifiedshowSpacefalse
reversetrue
typepage
labelsdistributed

...

This is a branch location in cologne which is managed remotely.

LocationCologne
IP-Address172.16.0.100

Central SONARPLEX

This is the network operation center where all alerts are collected form the remote locations.

LocationLondon
IP-Address172.16.0.254
azeti Agent Port

4192

azeti Agent PasswordHow-ToDM

The satellite device should send its status every 30 minutes and only HARD events should be sent.

The general procedure is as follows.

  1. Configure the Agent on the Central SONARPLEX
  2. Set the location identifier on the Satellite SONARPLEX
  3. Enable status and event delivery on the satellite
  4. Done.

Step-by-step guide

...

Central SONARPLEX

...

configuration

First set the azeti Agent credentials.

...

  1. Insert excerpt
    _OpenAdminWeb
    _OpenAdminWeb
    nopaneltrue
     > Configuration > Network > Agent Configuration
  2. Set Port to use: to 4192
  3. Set Agent Password :to How-ToDM (or any other)
  4. Click  to save the configuration

Satellite SONARPLEX configuration

Now open the administrative web interface of the Satellite SONARPLEX and set the location identifier. 

  1. Choose Configuration ::
    Insert excerpt
    _OpenAdminWeb
    _OpenAdminWeb
    nopaneltrue
     > Configuration >  My Properties 
    and scroll down to the bottom
  2. Open the resource LOCATION
  3. Set Ressource Value: Cologne
  4. Click  to save the configuration

Now enable the status and event delivery on the Satellite SONARPLEX.

...

  1. Insert excerpt
    _OpenAdminWeb
    _OpenAdminWeb
    nopaneltrue
     > Configuration
     > Status Delivery Configuration for Distributed Monitoring 
    and configure the settings like shown below.
Parameter NameSetting
Deliver Status at regular baseenable
Delivery Interval in Minutes (Heartbeat)30
Retry Frequency in Minutes5
Retry Attempts3
Deliver following Events immediately

Service Alerts

Host Alerts

Suppress SOFT State alerts

Deliver Performance Data

enable
Do not store performance data locallydisable
Destination Host (NOC)172.16.0.254 
Destination Agent Port4192
Destination Agent PasswordHowTo-DM 
Default service output upon transfer problemsMissing check result from satellite.
Default service state upon transfer problemsUNKNOWN
Retain state on outdated servicesenable
Debug LevelWARN
Tip

See the Status Delivery Configuration

...

for Distributed Monitoring article for a detailed explanation of the particular settings.

Verifying the Setup

...

All the satellite objects will appear on the destination device after a couple of minutes. The new objects will be prefixed by the location identifier (see above). All incoming status information is submitted passively. You should message similar like the shown excerpt.

Code Block
[2014-02-04 17:11:06] PASSIVE SERVICE CHECK: dm-test_-azeti-A-;dm-test_Software-Status;0;OK - FM-Usage: 0.22% - LOAD: 0.33
[2014-02-04 17:11:06] PASSIVE SERVICE CHECK: dm-test_-azeti-A-;dm-test_Monitoring;0;OK - 13 processes running, last status update 2 seconds ago
[2014-02-04 17:11:06] PASSIVE SERVICE CHECK: dm-test_-azeti-A-;dm-test_Watchdog-Status;0;OK - No problems within last recent hour

You can see the internal process of the distributed monitoring delivery right after it was enabled within the log files.

  • Distributed Monitoring (NOC Processor) [process_satellite.log]
  • Distributed Monitoring (Satellite Processor) [send_status.log]
  • Distributed Monitoring Event Log (NOC) [event.log]

Please keep in mind that only following service configuration objects will be synchronized in a distributed monitoring setup:

  • Notification timeperiod (if a timeperiod of the same name exists on NOC; use 24x7 otherwise)
  • Send notifications when service is in state
Info

All other service objects (like Notification frequency) will be generated out of default settings and can be configured differently on the NOC at any time.